Emergency Garage Door Repair

Why OnPoint Pro Doors

OnPoint Pro Doors handles garage door repair across the New York metro area — all five NYC boroughs, Long Island (Nassau and Suffolk), and Northern New Jersey. We are licensed, insured, and built around three commitments: same-day service for emergencies, up-front pricing before any tool comes out of the truck, and a written warranty on every job.

We service every major brand including LiftMaster, Genie, Chamberlain, Craftsman, Wayne Dalton, Amarr, Marantec, Linear, and Clopay. Our trucks are stocked with the most common springs, cables, rollers, opener boards, and panels so we complete the repair on the first visit roughly 92% of the time.

When you call, you get a real person — not a call center, not a scheduling robot. We ask three diagnostic questions, dispatch the right truck with the right parts, and get a technician on-site typically within 60 minutes during business hours.

Our Service Area

NYC: All five boroughs — Brooklyn, Queens, Manhattan, The Bronx, Staten Island. Long Island: Nassau County (Hempstead, Garden City, Massapequa, Hicksville, Levittown, and surrounding) and Suffolk County (Huntington, Smithtown, Babylon, Bay Shore, Patchogue, Riverhead, Hamptons). New Jersey: Hudson, Bergen, Essex, Union counties — Jersey City, Hoboken, Newark, Elizabeth, Bayonne, and surrounding.

What Customers Say

Real verified reviews on Thumbtack and Facebook from homeowners across our service area. We have a 4.9 / 5 average across 287+ reviews and counting:

Garage Door Safety — UL 325 Standard and Why It Matters

Federal UL 325 is the safety standard governing residential garage door openers. It exists because in the early 1990s, multiple children died in garage door accidents — doors closing on small bodies, doors falling because of broken safety systems. Every modern opener is required to meet UL 325, and we test compliance on every single job:

• Photo-eye reverse. The two photo-eye sensors near the floor must reverse the door if their beam is broken during closing. We test by walking through the beam path during a closing cycle. If it doesn't reverse instantly, we troubleshoot.
• Contact reverse. The door must reverse on physical contact with an obstacle. We test by placing a 2x4 block flat on the ground in the door path. The door must reverse upward within 2 seconds of contact.
• Force calibration. The opener's down-force setting controls how much resistance triggers a reverse. Set too high, the door can crush an obstacle before reversing. We calibrate per UL 325 using a force gauge.
• Manual release reachable. The red emergency-release cord must be accessible from inside the garage and rated to allow manual disengagement during a power outage.

If your door fails any of these tests, we don't leave until it's fixed — even if you didn't call us about safety. This is non-negotiable. Most "won't close" calls actually trace to a photo-eye misalignment which is a safety system catching a real problem; bypassing it is illegal under UL 325.

Inside Our Trucks — Why First-Visit Completion Hits 92%

National-franchise techs roll up to your house, do the diagnostic, then need to go order parts. We don't. Each of our service trucks is a rolling inventory built around the failure patterns we see across NYC, Long Island, and New Jersey:

• Torsion springs in 8 IPPT calibrations covering 95% of residential door weights from 130 lb to 320 lb
• Extension springs in 4 stretch ratings for older 7-foot doors
• Lift cables in 3 gauges (1/8", 5/32", 3/16") rated for door weights up to 400 lb
• Full sets of 13-ball-bearing nylon rollers (10 per door) for noise reduction upgrades
• 10 most common LiftMaster, Chamberlain, Genie logic boards including pre-2018 generation
• Photo-eye sensor pairs (LiftMaster, Chamberlain, Genie) including the green/red Sears-spec pairs for Craftsman openers
• Remote transmitters: Security+ 2.0, Genie Intellicode, Chamberlain Smart, Wayne Dalton, Marantec, Linear Megacode
• 16-foot rolls of EPDM bottom seal in 3 widths plus retainer track and end caps
• Replacement hinges (#1 through #5), bottom brackets, top brackets, jamb hardware, drum cones
• Winding bars in matched pairs, calibrated tension gauges, fish tape, multimeter, RF signal analyzer

That inventory is the reason 92% of jobs are completed on the first visit without ordering parts. The remaining 8% are usually obsolete pre-2010 units where a part has to be sourced from a regional distributor — we order same-day and return within 24-48 hours.

Up-Front Pricing — What You Actually Pay

Our pricing is the same across every neighborhood we serve. We don't charge more for "premium" zip codes or less for "competitive" ones. The diagnostic is free if you do the repair, and the price you approve in writing is the price on the invoice — period.

• Spring replacement (single): $180-$320
• Spring replacement (matched pair): $280-$520
• Cable replacement (both sides — required, never single): $180-$320
• Roller replacement (full 10-roller set, nylon 13-ball-bearing): $140-$240
• Off-track recovery (two-tech response, same day): $220-$420
• Photo-eye realignment & replacement: $79-$149
• Opener repair (logic board, sprocket, drive gear): $150-$280
• Full opener replacement (parts + install): $399-$680
• New door installation (single panel up to 8'×7'): $1,200-$2,400
• New door installation (double or carriage house up to 16'×8'): $1,800-$3,800
• Tune-up & maintenance (lubrication, balance, safety reverse, photo-eye): $129-$179
• Remote programming (per remote, OEM): $45-$89
• Keypad replacement (outdoor-rated): $129-$189
• Diagnostic visit (waived with repair): $0-$89

Payment: Visa / MasterCard / Amex / Discover, Zelle, ACH for commercial accounts, financing through our partner with instant approval at the truck on jobs over $1,000.